MITSUBISHI GB-100cnc GEAR HOB
- five-axis fanuc cnc control with conversational programming
- versitile –handles spur gears, helical gears, certain compound gears, worm gears, sprockets and splines
- wide ranging work piece handling –up to 40” maximum o.d. capacity, down to as litle as 1” o.d. over teeth
- dedicated bridge crane for large work pieces
- full complement of coated hobs and flexible tooling for rigid setups
- runs diametral pitch and module pitch system gears with no complex change-gear calculations. all cnc controlled
OKUMA & HOWA MILLAC 415V MACHINING CENTER
- 10hp, 8000 rpm, cat-40 spindle units
- rapid traverse rates: 1180ipm (xy), 708ipm (z)
- travel: x-22.05”, y-16.14”, z-1614”
- 16 pot toolmagazines
- high speed tool changes and rapid positioning for reduced cycle times
- flexible tooling for a variety of work piece holding options
- typical applications include small parts requiring high feed rates and spindle speeds
- for finish requirements, numerical scribing of “flat” parts such as heads and dial rings
OKUMA & HOWA V-80R VERTICAL TURNING CENTER
- our largest, most powerful cnc lathe
- 40 hp, 600 rpm spindle drive unit
- 630ipm rapid traverse rates
- up to 38” max turning diameter, 33” maximum workpiece length depending on rigidity of setup
- no tailstock, used primarily for large o.d. work pieces of less than 12” length
- complete cnc turning, drilling, contouring and threading operations
- fanuc cnc control unit
OKUMA & HOWA 4thAXIS 414H HORIZONTAL MACHINING CENTER
10hp, 10,000 rpm, cat-40 spindle unit
dedicated, simultaneous 4-axis operation
travel: x-16”, y-13.5”, z-16”
24 pot tool magazine
3.5 second chip-to-chip tool change cycle
rapid traverse rate: 1417 ipm (xyz)
feed rated up to 394ipm on all axes
flexible tooling and fixtures for quick setup of diverse jobs
OKUMA & HOWA MILLAC 852 MACHINING CENTER
20hp, 6000 rpm, cat-50 spindle unit
20hp, 6000 rpm, cat-50 spindle unit
travel: x-80”, y-33.46”, z-29-52”
large work table offers a variety of setup options
routinely used for work pieces over 144” oal
630 i.p.m. rapid traverse rates (x,y,z)
36 pot tool magazine
fanuc three-axis cnc control
OKUMA & HOWA ACT-35 CNC TURNING CENTER
up to 13.5” o.d. capacity
26” maximuim work piece length with tailstock
3500 rpm spindle drive
BEAVERMATIC HEAT TREAT CAPABILITIES
carburizing
carbon nitriding
through hardening of steels up to 1650of
annealing –stress relief
normalizing
working dimensions –width: 18”, length: 24”, height: 14”
air & oil quench
temper
MORI-SEIKI NL3000\700
maximum od turning diameter 16.54”
maximum od turning length 28”
3000 rpm
25 hp
(2) OKUMA & HOWA MILLAC 3VA MACHINING CENTERS
10hp, 6000 rpm cat-40 spindle drive units
travel: x-22.9” y-14.13” z-17.5”
rapid traverse rates: 630ipm (xy) 470 imp (z)
20 pot tool magazines
flexible tooling and fixturing for quick setups
MORI-SEIKI MV-55 MACHINING CENTER
15hp, 3000rpm, cat-50 spindle unit
travel: x-40”, y-21.63”, z-17.7”
rapid traverse rate: 394ipm (xyz)
3-axis fanuc cnc control
MORI-SEIKI NL SL-403B
maximum od turning diameter 24.4”
maximum od turning length 37.7”
2400 rpm
40 hp
787.4 ipm rapid traverse
MORI-SEIKI NL NL2500\700
maximum od turning diameter 14.02”
maximum od turning length 27.76”
4000 rpm
22 hp
OKUMA & HOWA MILLAC 438V MACHINING CENTER
25hp, 10,ooo rpm, cat-40 spindle unit
travel: x-32.25”, y-16.9”, z-17.5”
rapid traverse rate: x, y-797 ipm, z-630ipm
20 pot tool magazine
MORI-SEIKI SL-3 CNC TURNING CENTER
9” max o.d. capacity
30” max length with tailstock
4000 rpm spindle drive unit
conversational programming built into fanuc cnc control
full cnc turning, contouring and o.d./i.d. threading capabilities
MITSUBISHI LASER
- 48” x 96” sheets
- tool steels -.750
- aluminum -.375
- stainless steel -.500
- nylatron -.250
OKUMA & HOWA ACT-4 TURNING CENTER
14” max o.d. capacity
18” max length with tailstock
1780 rpm spindle drive unit
fanuc cnc control with conversational programming
complete range of cnc turning and threading
staffed by experienced cnc machinists with programming skills, as opposed to a basic operator, allows self-sufficient production in each cell
BRIDGEPORT-TYPE VERTICAL KNEE MILL
2hp variable speed r8 spindles
digital readouts on x and y axes
right-angle heads for advanced setup requirements
full complement of carbide insert and conventional tooling
experience manual machinist staff and advanced manual machining capabilities to support our considerable cnc resources
MANUAL ENGINE LATHE
nardini in-2560-t lathe, 29” o.d. with gap bed, 72” between centers with dro system
full complement of carbide insert and conventional tooling
MANUAL ENGINE LATHE #2
toolmex lathe, 24” o.d., 96” between centers with sony dro system
full complement of carbide insert and conventional tooling
BLANCHARD No. 18 GRINDER, 2002 OVERHAUL
42” magnetic chuck with solid-state electronic controller
50hp spindle motor
used for grinding of ferrous metal components to tolerances of +/-.001”
BLANCHARD No. 20D GRINDER, 2002 OVERHAUL
36” magnetic chuck with solid-state electronic magnet controller
50hp spindle motor
used for grinding of ferrous parts to tolerances of +/-.001”
DAITO GA660 CUTOFF SAW
26” round stock capacity
cuts bundles up to 13” x 26”
fully programmable nc control
